Wheel Offset Calculator
Enter a wheel’s width and backspacing to work out its offset in millimeters and inches — or enter an offset to see what it means.
Wheel Offset Calculator calculates in your browser.
Where does the wheel’s mounting face sit?
Wheel offset is the distance from the wheel’s centerline to the mounting face that bolts to the hub. Positive offset puts the mounting face toward the street side, tucking the wheel in; negative offset puts it toward the vehicle, pushing the wheel out; zero puts it in the middle.
If you can measure the backspacing, the calculator finds the offset. It needs the overall width across both flanges — wider than the nominal width on the label — so you either enter a measured overall width or use a flange allowance, which is marked as assumed in the result.
How to use the Wheel Offset Calculator
- Choose whether you know the backspacing or already know the offset.
- Enter the wheel’s nominal width and how to find the overall width: a flange allowance (0.5 in each side to start) or a measured width.
- Enter the backspacing, measured from the back flange edge to the mounting face.
- Read the offset, its sign, and where the mounting face sits.
How the calculation works
Overall width = nominal width + 2 × flange allowance (or measured)
Centerline = overall width ÷ 2 from the back edge
Offset = backspacing − overall width ÷ 2
Millimeters = inches × 25.4
Positive offset: mounting face toward the street side of the centerline. Negative: toward the vehicle.
| Wheel | Overall width | Backspacing | Offset |
|---|---|---|---|
| 8 in | 9 in (assumed) | 5.88 in | +35.1 mm |
| 8 in | 9 in (assumed) | 6 in | +38.1 mm |
| 8 in | 9 in (assumed) | 4 in | −12.7 mm |
| 8 in | 8.9 in (measured) | 5.88 in | +36.3 mm |
Calculated on your device
- The calculation runs in your browser as you type; nothing is sent to a server.
- Your wheel measurements and results are not sent to Looty Tools or stored.
- The calculator area is masked from session-recording analytics.
Limitations
- An assumed flange allowance is an estimate; real flanges vary, so a measured overall width is more accurate.
- Offset alone doesn’t confirm fit — bolt pattern, center bore, brake clearance, load rating, and the tire matter too.
- Backspacing must be measured to the flat mounting face, not a raised center or hub ring.
- Wheel positions only; it doesn’t model suspension, steering, or tire bulge.
Related calculators
- Tire Size Comparison CalculatorCompare two tire sizes.
- Wheel Backspacing CalculatorFind a wheel's backspacing.
- Wheel Poke & Inner Clearance CalculatorEstimate how far a wheel sticks out and how much inner clearance is left.
- Length ConverterConvert inches, feet, meters, and other lengths.
Guides
- What Wheel Offset IsWhat wheel offset means, where the centerline and mounting face are, how an ET marking reads, and how to measure offset on a wheel at home.
- Positive vs Negative OffsetWhat positive, zero, and negative wheel offsets mean, which vehicles tend to use each, and how each one changes where the wheel sits.
- Offset From BackspacingCalculate wheel offset from backspacing and wheel width, with a flange allowance or a measured overall width, and see how much the width choice matters.
- Calculating BackspacingWork out wheel backspacing and frontspacing from the wheel’s width and offset, in inches or millimeters, with worked examples for car and truck wheels.
- Offset vs BackspacingHow wheel offset and backspacing differ, why the same backspacing gives different offsets on different widths, and which measurement each market uses.
Wheel Offset Calculator FAQ
- How do I find wheel offset from backspacing?
- Subtract half the wheel’s overall width from the backspacing. An 8-inch wheel that is 9 inches overall, with 5.88 inches of backspacing, has an offset of about +35.1 mm.
- Why does the calculator ask for a flange allowance?
- Backspacing is measured from the outer edge of the back flange, but the label width is measured inside the flanges. The allowance — 0.5 inches per side to start — adds the flanges back.
- What does a negative offset mean?
- The mounting face sits on the vehicle side of the centerline, so more of the wheel sticks out. On a 9-inch overall width, backspacing under 4.5 inches gives a negative offset.
- What does ET mean on a wheel?
- ET is the offset in millimeters: ET35 is +35 mm. A minus sign means negative offset.
- Does the right offset mean the wheel fits?
- No. Width, diameter, bolt pattern, center bore, brake clearance, and the tire all matter. Check the vehicle maker’s specifications or a wheel professional.
- Are the tire sizes, distances, and prices I enter sent anywhere?
- No. The calculation runs in your browser as you type. The sizes, distances, fuel economy, prices, costs, and results you enter are not sent to Looty Tools or stored, and the calculator area is masked from session-recording analytics. Refreshing the page clears it.


