Wheel Backspacing Calculator
Enter a wheel’s width and offset to see its backspacing and frontspacing in inches and millimeters.
Wheel Backspacing Calculator calculates in your browser.
How much of the wheel sits behind the hub?
Backspacing is the distance from the wheel’s back (inner) flange edge to its mounting face. It shows how much of the wheel sits inboard of the hub — the part that has to clear struts, springs, and control arms. Frontspacing is the rest of the width, out to the front flange.
Enter the nominal width from the wheel’s label and its offset, positive or negative. The calculation needs the overall width across both flanges, so it starts from a flange allowance of 0.5 inches per side, marked as assumed, unless you enter a measured overall width.
How to use the Wheel Backspacing Calculator
- Pick inches or millimeters for the width, and enter the wheel’s nominal width.
- Keep the flange allowance, change it, or choose a measured overall width.
- Enter the offset in millimeters or inches — type a minus sign for a negative offset.
- Read the backspacing, frontspacing, and the overall width used.
How the calculation works
Overall width = nominal width + 2 × flange allowance (or measured)
Backspacing = overall width ÷ 2 + offset
Frontspacing = overall width − backspacing
Offsets in millimeters are converted to inches (÷ 25.4) before adding.
| Wheel | Offset | Overall width | Backspacing | Frontspacing |
|---|---|---|---|---|
| 8 in | +35 mm | 9 in (assumed) | 5.88 in (149.3 mm) | 3.12 in (79.3 mm) |
| 10 in | −12 mm | 11 in (assumed) | 5.03 in (127.7 mm) | 5.97 in (151.7 mm) |
| 7 in | +40 mm | 8 in (assumed) | 5.57 in (141.6 mm) | 2.43 in (61.6 mm) |
| 8 in | +35 mm | 8.9 in (measured) | 5.83 in (148 mm) | 3.07 in (78 mm) |
Calculated on your device
- The calculation runs in your browser as you type; nothing is sent to a server.
- Your wheel measurements and results are not sent to Looty Tools or stored.
- The calculator area is masked from session-recording analytics.
Limitations
- An assumed flange allowance is an estimate; a measured overall width gives a more accurate figure.
- Backspacing alone doesn’t confirm fit — brakes, suspension, steering, and the tire set the real limits.
- An offset larger than half the overall width is rejected, because the mounting face would be outside the wheel.
- Wheel positions only; tire sidewall bulge isn’t included.
Related calculators
- Tire Size Comparison CalculatorCompare two tire sizes.
- Wheel Offset CalculatorFind a wheel's offset.
- Wheel Poke & Inner Clearance CalculatorEstimate how far a wheel sticks out and how much inner clearance is left.
- Length ConverterConvert inches, feet, meters, and other lengths.
Guides
- What Wheel Offset IsWhat wheel offset means, where the centerline and mounting face are, how an ET marking reads, and how to measure offset on a wheel at home.
- Calculating BackspacingWork out wheel backspacing and frontspacing from the wheel’s width and offset, in inches or millimeters, with worked examples for car and truck wheels.
- Offset vs BackspacingHow wheel offset and backspacing differ, why the same backspacing gives different offsets on different widths, and which measurement each market uses.
- Wheel Width and BackspacingNominal vs overall wheel width, where the flanges come in, and how much backspacing changes when the width is assumed instead of measured.
- Offset and Inner ClearanceHow offset and width changes move a wheel’s inner lip toward or away from the suspension, and how to work out the clearance left from a measurement.
Wheel Backspacing Calculator FAQ
- How do I calculate backspacing from offset?
- Add the offset to half the overall width, in the same unit. An 8-inch wheel at +35 mm, 9 inches overall, has about 5.88 inches of backspacing.
- Why is the overall width bigger than the wheel width?
- The label width is measured between the bead seats. The flanges add roughly half an inch each side, and backspacing is measured to the flange edge.
- How does a negative offset change backspacing?
- It reduces it: the offset is subtracted from half the width. A 10-inch wheel at −12 mm, 11 inches overall, has about 5.03 inches.
- What is frontspacing?
- The distance from the mounting face to the front (outer) flange edge — the overall width minus the backspacing.
- Can I enter everything in millimeters?
- Yes. Pick millimeters for the width and the offset; switching units converts what you typed.
- Are the tire sizes, distances, and prices I enter sent anywhere?
- No. The calculation runs in your browser as you type. The sizes, distances, fuel economy, prices, costs, and results you enter are not sent to Looty Tools or stored, and the calculator area is masked from session-recording analytics. Refreshing the page clears it.


