Pallet Overhang Calculator
Enter a pallet’s length and width and the load’s footprint in inches, feet, centimeters, or millimeters to see how far the load reaches past each edge — centered or shifted.
Pallet Overhang Calculator calculates in your browser.
Overhang and unused pallet space are different problems
A load that is bigger than its pallet hangs over the edges, and those carton edges have nothing under them. A load that is smaller leaves strips of deck showing — wasted pallet space, but nothing unsupported. Comparing only the totals hides which one you have, and where.
This calculator works out every edge separately. Enter the pallet and the load’s footprint at its widest point; by default the load is centered, so any overhang is split evenly. Switch to a shifted load to see what happens when it sits closer to one end or side, and add your own allowance to compare against.
How to use the Pallet Overhang Calculator
- Choose inches, feet, centimeters, or millimeters.
- Enter the pallet’s length and width.
- Enter the load’s length and width at its widest point, measured the same way round as the pallet.
- Leave the load centered, or choose Shifted off center and enter how far it has moved toward one end and one side.
- Optionally enter the most overhang you allow per edge, to compare against.
How the calculation works
Overhang at each end = (load length − pallet length) ÷ 2
Overhang at each side = (load width − pallet width) ÷ 2
Shifted load: near edge = (load − pallet) ÷ 2 + shift; far edge = (load − pallet) ÷ 2 − shift
A negative result is pallet deck left showing, not overhang
Overhang area = load area − the area where load and pallet overlap
Each edge is worked on its own, so a load can overhang the ends and still leave deck showing along the sides. Areas come from where the two rectangles actually overlap, which keeps shifted loads correct.
| Pallet and load | Placement | Largest overhang | Each end | Each side |
|---|---|---|---|---|
| 48 × 40 in pallet, 50 × 42 in load | Centered | 1 in | 1 in overhang | 1 in overhang |
| 48 × 40 in pallet, 46 × 38 in load | Centered | None | 1 in of pallet showing | 1 in of pallet showing |
| 1,200 × 800 mm pallet, 1,240 × 800 mm load | Centered | 20 mm | 20 mm overhang | Flush with the edge |
Calculated on your device
- The calculation runs in your browser as you type; nothing is sent to a server.
- Your sizes, weights, and results are not sent to Looty Tools or stored.
- The calculator area is masked from session-recording analytics.
Limitations
- It uses the load’s footprint at its widest point. A load that bulges or leans can reach further than its base.
- It treats the pallet and load as rectangles seen from above. Height, weight, stacking strength, and stability aren’t checked.
- An allowance you enter is your own figure. The calculator doesn’t know any carrier’s, warehouse’s, or customer’s rules, and comparing with it isn’t approval.
- Measure the pallet you are using: pallets sold under the same nominal size can differ slightly.
Related calculators
- Box Volume CalculatorFind the volume of a box from its dimensions.
- Package Density CalculatorFind how dense a package is from its weight and volume.
- Box Clearance CalculatorSee how much space is left inside a box.
Guides
- Calculating Pallet OverhangA step-by-step method for working out how far a load overhangs each edge of a pallet, with centered and off-center examples in inches and millimeters.
- Overhang vs Unused SpaceWhy a load that hangs past a pallet edge and a load that leaves deck showing are different problems, and how to measure and weigh each one.
- Fixing Pallet OverhangPractical ways to remove pallet overhang — re-centering the load, turning it, changing the stacking pattern, or using a larger pallet — with worked figures.
Pallet Overhang Calculator FAQ
- How do I calculate pallet overhang?
- Subtract the pallet’s length from the load’s length and halve it for each end; do the same with the widths for each side. A 50 × 42 in load centered on a 48 × 40 in pallet overhangs 1 in on every edge.
- What if the load is smaller than the pallet?
- Then there is no overhang. The negative difference is pallet deck left uncovered — unused space. A 46 × 38 in load centered on a 48 × 40 in pallet leaves 1 in of deck showing on every edge.
- How does an off-center load change the overhang?
- Shifting the load moves overhang from one edge to the opposite one. A 46 in long load shifted 3 in toward one end of a 48 in pallet overhangs that end by 2 in and leaves 4 in of deck showing at the other.
- Can turning the load reduce overhang?
- Often. If the load’s longer side runs across the pallet’s shorter side, turning it 90° can bring it inside the edges. The calculator says when turning a centered load would lower the largest overhang.
- How much overhang is acceptable?
- That depends on whoever handles and ships the pallet. Enter their allowance to compare against; the calculator doesn’t know any carrier’s rules, and an allowance you enter isn’t approval or a safety rating.
- Are the sizes, weights, and prices I enter sent anywhere?
- No. The calculation runs in your browser as you type. Your sizes, weights, prices, and results are not sent to Looty Tools or stored, and the calculator area is masked from session-recording analytics. Refreshing the page clears it.


