Shipping & packaging
How to Calculate Pallet Overhang
Pallet overhang is the distance a load reaches past the edge of the pallet underneath it. It takes one subtraction and one division per direction — but it has to be done for each edge, because a load can overhang one way and fall short the other.
Ready to try the tool this guide describes?
Measure the right things
Measure the pallet’s deck length and width, then the load’s footprint at its widest point — usually the bottom layer, but sometimes a bulging middle layer or a top tier stacked out of line. Measure both in the same unit and the same way round: the load’s length along the pallet’s length.
Work out each direction
Subtract the pallet size from the load size and halve the difference. With the load centered, that half lands on each of the two opposite edges.
- Ends: (load length − pallet length) ÷ 2.
- Sides: (load width − pallet width) ÷ 2.
- A positive answer is overhang; a negative one is deck left showing.
Worked examples
| Pallet | Load (centered) | Each end | Each side |
|---|---|---|---|
| 48 × 40 in | 50 × 42 in | 1 in overhang | 1 in overhang |
| 48 × 40 in | 48 × 44 in | Flush with the edge | 2 in overhang |
| 1,200 × 800 mm | 1,240 × 800 mm | 20 mm overhang | Flush with the edge |
| 1,200 × 1,000 mm | 1,180 × 1,030 mm | 10 mm of pallet showing | 15 mm overhang |
When the load isn’t centered
Real loads drift. If the load sits closer to one end, the overhang at that end grows by the shift and the opposite end loses the same amount. A 50 in long load on a 48 in pallet, shifted 1.5 in toward one end, overhangs that end by 2.5 in, while the other end ends up with half an inch of deck showing.
Area, not just distance
Overhang distances say how far; area says how much. For the 50 × 42 in load on a 48 × 40 in pallet, the load covers 2,100 in² and the pallet 1,920 in², so 180 in² — about 8.57% of the load’s footprint — has nothing under it.
Calculating Pallet Overhang FAQ
- Do I measure pallet overhang from the top or the bottom of the load?
- From wherever the load is widest. The bottom layer usually sets the footprint, but a bulging or misaligned layer higher up can overhang more than the base.
- Can a load overhang on one side and not the other?
- Yes, if it isn’t centered or if only one of its dimensions is bigger than the pallet. Each edge is worked separately for that reason.
- What does a negative overhang figure mean?
- That the load stops short of that edge, leaving pallet deck uncovered. It isn’t overhang; it is unused pallet space.
- How much overhang does a 50 × 42 in load have on a 48 × 40 in pallet?
- 1 in on every edge when centered: (50 − 48) ÷ 2 at each end and (42 − 40) ÷ 2 at each side.
- Why halve the difference between load and pallet?
- Because a centered load shares its extra length between two opposite edges. Without halving you get the total overhang along that direction, not the amount at each edge.
Related guides
- Overhang vs Unused SpaceWhy a load that hangs past a pallet edge and a load that leaves deck showing are different problems, and how to measure and weigh each one.
- Fixing Pallet OverhangPractical ways to remove pallet overhang — re-centering the load, turning it, changing the stacking pattern, or using a larger pallet — with worked figures.
Open the tool
Jump into Pallet Overhang Calculator when you are ready to process your files.


